4/0 Aluminum Wire Ampacity
4/0 aluminum wire is commonly rated for approximately 180 to 205 amps under typical conditions, but the actual permitted ampacity depends on the cable type, installation method, terminals, and required derating. A 4/0 marking alone is not enough to make a final selection for a service or feeder. Use the cable’s exact listing and the conditions of the installed circuit to make the final selection.
| Situation | Working Ampacity Answer | What Determines the Final Result |
|---|---|---|
| Typical 4/0 aluminum service or feeder conductor | 180 to 205 amps | Insulation rating, terminals, installation method, ambient temperature, and conductor count |
| 4/0 aluminum URD cable | A 300-foot, 240-volt 4/0 triplex run may be adequate depending on the load, conductor construction, circuit configuration, ampacity, and voltage drop. | The manufacturer’s duct or direct-burial rating for that exact cable |
| 4/0 aluminum aerial triplex | No blanket rating | The triplex construction, messenger/neutral design, insulation, and aerial listing |
| Long run | Ampacity alone is not enough | Voltage-drop calculation as well as thermal ampacity |
What 4/0 Aluminum Ampacity Means
Ampacity is the amount of electrical current a conductor can carry under specified conditions without overheating its insulation or connected equipment. It is not simply a property of the metal size stamped on the cable.
“4/0,” also called “four aught,” is much larger than 4 AWG. The slash and zeroes matter: 4 AWG and 4/0 AWG are different conductor sizes and should never be treated as interchangeable.
Aluminum and copper also do not have the same ampacity at the same AWG or kcmil size. Aluminum generally needs a larger conductor size than copper for the same job, and its terminations must be suitable for aluminum conductors.
The final allowable ampacity can be limited by:
- The conductor material and size
- Insulation type and temperature rating
- Whether the cable is in conduit, direct buried, free air, or installed as a cable assembly
- Ambient temperature
- The number of current-carrying conductors grouped together
- The temperature rating and aluminum compatibility of lugs, breakers, disconnects, and panel equipment
- Local electrical-code requirements
How to Select 4/0 Aluminum Wire Ampacity
Selecting 4/0 aluminum wire ampacity requires matching the exact cable and installation method to its manufacturer documentation.
Step 1: Identify the Exact Cable, Not Just the Conductor Size
Start with the full printing on the cable jacket or reel tag. Record the conductor size, aluminum designation, insulation type, cable family, voltage rating, and intended installation method.
A 4/0 aluminum conductor in SER cable, mobile-home feeder, aerial triplex, USE-2, XHHW-2, or medium-voltage URD is not automatically the same product for ampacity purposes. Each has a different construction and listing.
For example, Priority Wire’s #4070-06 is a 15 kV medium-voltage cable for underground distribution. Its construction includes 220-mil insulation and an 11-strand No. 14 concentric neutral. The aluminum conductor diameter is 0.515 inches, but that is not the diameter to use for conduit planning because the completed cable is much larger.
That named Priority Wire product is suitable for wet or dry locations at circuit voltages of 15,000 volts or less. Confirm the voltage rating from the cable marking and manufacturer data sheet for the exact cable you are buying; a 15 kV URD rating does not make a cable automatically appropriate for every low-voltage service installation.
Step 2: Match the Ampacity to the Actual Installation Method
Select the rating that matches where the cable will physically run: in duct, directly buried, aerial, or inside a listed cable assembly. Do not choose the highest number on a data sheet if it describes a different installation.
For the specific Priority Wire #4070-06 4/0 stranded 15 kV aluminum URD cable, the manufacturer’s ampacity is 241 A at 90°C when installed in duct and 320 A at 90°C when directly buried. Those are installation-specific ratings for that medium-voltage URD product, not a universal ampacity for all 4/0 aluminum wire.
Use the exact manufacturer data sheet for the cable you have and select the column that matches the completed installation. A cable routed partly in conduit and partly in earth may need a design review based on the conditions of each portion.
Use duct and direct-burial values only for the installation method they describe. Each 4/0 aluminum cable product needs its own manufacturer documentation.
Step 3: Check the Normal Temperature Rating and Terminations
A conductor’s insulation rating is only one part of the circuit rating.
Priority Wire rates its named 15 kV URD cable for 90°C continuous operation, 130°C emergency operation, and 250°C short-circuit operation. Only the 90°C continuous rating applies to normal load planning. The emergency and short-circuit temperatures are fault or abnormal-condition ratings, not targets for ordinary operation.
The usable circuit ampacity is limited by the lowest-rated part of the completed connection, not by the highest temperature printed on the cable.
For example, a 90°C-insulated conductor may still need to be evaluated using a 75°C or 60°C terminal limitation. Confirm that every termination is listed for the conductor material and conductor size being used.
Also account for conditions that create more heat around the conductors. Higher ambient temperature and more than three current-carrying conductors in a raceway or cable can require ampacity adjustments.
Step 4: Size for the Load and Check Voltage Drop Separately
Determine the circuit’s calculated load, overcurrent protection, and whether the load will operate for extended periods. Then compare that requirement with the allowable ampacity after all applicable limitations and adjustments.
A service or feeder is not automatically a match for 4/0 aluminum. The wiring method, equipment ratings, and calculated load all matter. Service or feeder rules also apply.
Ampacity and voltage drop are separate sizing checks: a conductor can have enough thermal ampacity but still create unacceptable voltage drop over a long run.
Circuit voltage does not increase the thermal ampacity of a conductor. A 240-volt feeder needs a voltage-drop calculation based on the intended load and complete circuit design before you decide whether 4/0 aluminum is sufficient or whether a larger conductor is needed.
Step 5: Plan Conduit, Pulling, and Delivery Using the Complete Cable Size
Use the outside diameter and weight of the finished cable assembly, not the bare-conductor diameter, when planning conduit, pulling equipment, bends, and delivery.
For the named Priority Wire 4/0 stranded URD construction, the overall jacket diameter is 1.31 inches and the listed net weight is 803 pounds per 1,000 feet. Those dimensions apply to that exact insulated, shielded cable with its concentric neutral; another 4/0 aluminum cable can have a very different outside diameter and weight.
Confirm conduit fill, pulling tension, bend limitations, and handling plans from the applicable installation requirements and the exact cable manufacturer’s documentation. Insulation, shielding, neutral wires, and jacket add substantial bulk.
Step 6: Document the Selection Before Installation
Before buying or installing the cable, make sure the job file includes:
- The complete cable designation from the reel or jacket
- The manufacturer’s data sheet for that exact cable
- The actual installation method
- The selected ampacity column and any adjustments
- Terminal temperature and aluminum-conductor compatibility
- The calculated load and overcurrent-protection design
- A voltage-drop calculation for long feeders
- Conduit and pulling information based on the complete cable diameter
Have the final design checked under the electrical code adopted where the work will be installed. For a new service, feeder, or underground distribution run, the installer, authority having jurisdiction, and electrical-equipment requirements control the finished approval.
Why URD, SER, and Aerial Triplex Cannot Share One Rating
URD Cable
URD stands for underground residential distribution, but the construction can range from low-voltage direct-burial conductors to shielded medium-voltage primary cable. The Priority Wire cable discussed here is intended for underground distribution, either direct buried or installed in duct.
Its manufacturer allows normal operation up to 90°C. That does not mean every cable marked URD has the same temperature rating, voltage rating, conductor construction, or ampacity.
SER Cable
Use the exact cable documentation to determine its construction and permitted uses. Its ampacity depends on the conductor count, insulation, jacket, installation location, terminals, and listing.
Aerial Triplex
The shorthand “4/0 4/0 4/0 triplex” does not reveal enough to assign an ampacity because it leaves out the exact construction, insulation, neutral or messenger design, voltage class, and product listing.
The manufacturer’s documentation identifies the ampacity for the exact triplex assembly and its aerial listing.
Long Runs and 200-Amp Applications
Evaluating a long 200-amp application requires the actual load, circuit voltage, conductor arrangement, and route length.
For typical 4/0 aluminum applications, 180 to 205 amps is a common range, but it does not replace a design check.
A useful way to frame the decision is:
- Verify that the cable is listed for the location and wiring method.
- Establish the permitted ampacity from the exact product documentation.
- Apply all terminal and installation limitations.
- Compare the resulting allowable ampacity with the calculated load and protective device.
- Perform a voltage-drop calculation for the actual route.
- Increase conductor size if either the ampacity or voltage-drop result requires it.
Confirm the Selection Before You Buy or Energize
Use this final check before ordering cable or completing the installation:
- The cable jacket matches the product data sheet.
- The cable’s voltage rating suits the circuit.
- The installation method matches the selected ampacity rating.
- The terminals are listed for aluminum and for the conductor size.
- The terminal temperature limitation has been considered.
- Ambient temperature and grouped conductors have been accounted for.
- The conductor has enough ampacity for the calculated load.
- A long-run voltage-drop calculation has been completed.
- Conduit fill and pulling plans use the complete cable diameter.
- The installation has been reviewed and approved as required locally.
For a 200-amp or 300-foot project, bring the cable data sheet, route drawing, load information, and equipment-terminal details to the electrician or permitting authority before purchasing the conductor.
Frequently Asked Questions
What amperage is 4/0 aluminum good for?
4/0 aluminum is commonly used in the 180 to 205 amp range for typical low-voltage service or feeder conditions. The final permitted ampacity can be lower or different because cable construction, terminations, ambient temperature, conductor grouping, and installation method all affect the result.
A specialty cable can have manufacturer ratings outside that general range. For example, medium-voltage URD cable may have separate ratings for duct and direct-burial installation.
Can 4 gauge wire handle 200 amps?
No. 4 AWG is not the same size as 4/0 AWG, and it should not be treated as a substitute for 4/0 aluminum in a 200-amp discussion. The “4/0” marking means four aught, a substantially larger conductor than 4 AWG.
Always read the full conductor marking before comparing wire sizes or shopping for cable.
Is 4/0 4/0 4/0 triplex OK for 240 volts at 300 feet?
No. The “4/0 4/0 4/0” size shorthand does not identify the aerial triplex construction or its permitted ampacity. A 300-foot, 240-volt run needs both the exact aerial-triplex ampacity from its manufacturer and a voltage-drop calculation based on the actual load and circuit configuration.
The triplex cable’s insulation, neutral or messenger construction, and product listing determine its allowable ampacity. For this 300-foot, 240-volt run, compare the product-specific ampacity with the voltage-drop calculation.
What is the ampacity of 4/0 aluminum SER cable?
There is no single ampacity for all 4/0 aluminum cable. The correct value comes from the exact cable documentation, installation method, terminal ratings, and applicable electrical requirements.
For 4/0 aluminum SER cable, use the value that matches its installation method, terminal ratings, and applicable electrical requirements—not a typical range for another cable type.
Does 90°C insulation let me use the 90°C ampacity column?
Not automatically. A 90°C conductor can only be used at that temperature basis when the entire installation, including the terminals and equipment, permits it.
For normal operation, the Priority Wire 15 kV URD cable discussed here is limited to 90°C continuous service; its 130°C emergency and 250°C short-circuit ratings are not normal-load ampacity ratings.
