How to Drill Into Aluminum Without Damaging It
You can drill aluminum cleanly with a sharp bit, firm workholding, cutting lubricant, and a steady feed that makes chips instead of rubbing the metal. Aluminum is easy to cut compared with steel, but it is soft and sticky, so a dull bit or packed flutes can create heat, long stringy chips, and rough holes. The method below works for most aluminum sheet and plate with a hand drill or drill press.
Why Aluminum Can Be Tricky to Drill
Aluminum does not usually resist the drill the way steel does. Its main challenge is that it can smear onto the cutting edges instead of forming and clearing a chip. This buildup is called a built-up edge, and it makes the bit cut poorly, run hot, and leave a rough or oversized hole.
Long chips are the other common problem. A chip can wrap around the drill shank, clog the flutes, or become trapped in a deep hole. Once the drill is rubbing rather than cutting, heat rises quickly.
A clean aluminum hole depends more on chip control and workholding than on brute force.
A drill press gives the best control for straight, accurate holes. A hand drill works well for sheet, installed parts, and ordinary holes when the aluminum is securely clamped.
How to Drill Aluminum Cleanly
Choose the setup that matches the job before marking the hole.
| Job | Best Starting Tool | Main Concern |
|---|---|---|
| Ordinary hole in aluminum plate | Sharp HSS twist drill | Keep the work clamped and clear chips |
| Thin sheet | Step drill or sharp twist drill with wood backing | Prevent snagging and distortion |
| Deep hole | Aluminum-specific drill with open flutes | Remove chips before they pack |
| Large, accurate hole | Drill press, milling machine, boring tool, or circular interpolation | Keep the hole round and on size |
| Hole near an edge | Supported sheet or plate clamped between backing pieces | Prevent grabbing and bending |
Step 1: Mark and Clamp the Workpiece
- Mark the center of the hole with a layout mark, marker, or scribe.
- For plate and thicker stock, make a light center-punch mark to keep the drill point from wandering. Avoid a heavy punch mark in thin sheet because it can dent or distort the metal.
- Put a flat sacrificial wood board beneath the aluminum. The board supports the metal as the drill exits and reduces burrs on the back.
- Clamp the aluminum and backing board to the drill-press table or workbench. Never hold the workpiece by hand while drilling; a bit can catch and spin the metal suddenly.
- Wear eye protection and keep loose sleeves and jewelry away from the rotating tool.
If the hole must be perpendicular, check that the drill press table is square to the bit before starting.
Step 2: Choose a Sharp Drill Bit
For most home-shop holes, a sharp high-speed steel (HSS) twist drill is the practical choice for aluminum. Use a bit with clean, sharp cutting edges; a dull bit rubs, heats the metal, and is more likely to smear aluminum into its flutes.
With Regal Cutting Tools’ aluminum drills, sharp cutting edges are intended to reduce aluminum “mush” and built-up edge rather than merely rubbing the material. That same principle applies when deciding whether an ordinary twist bit is still sharp enough to use.
For holes where chips may pack in the flutes, especially deep holes or soft aluminum, specialized aluminum drills are useful:
- Regal Cutting Tools uses an open, parabolic-flute design in its aluminum drilling guidance to move chips out of the hole.
- Its three-flute aluminum drill configuration balances drill strength with chip handling.
- Polished flutes with aggressive angles of 45 degrees or more help eject the long chips aluminum can produce. This is flute geometry, not the point angle at the drill tip.
Step 3: Set the Drill for Cutting, Not Rubbing
There is no single RPM that fits every aluminum hole: small drill bits can run faster than large-diameter tools, while larger cutters need lower spindle speed. Set the drill according to the bit diameter and use a speed chart supplied for that drill or cutter when one is available.
Aluminum can tolerate relatively high spindle speeds, but speed only works when the drill is advancing enough to cut a chip. High RPM combined with very light pressure lets the bit rub against the aluminum, generating heat without removing material effectively.
Apply cutting fluid made for aluminum to the drill point and hole location. The lubricant reduces friction and helps prevent aluminum from sticking to the cutting edges. Reapply it if the hole is deep or the bit begins to look dry.
Step 4: Drill With Steady Feed Pressure
- Align the drill point with the center mark and start the drill.
- Lower the bit into the aluminum with steady, positive pressure. The drill should form visible chips or curls, not a fine rubbed dust.
- Keep the drill straight. A hand drill should be held square to the work; a drill press should feed straight down without forcing the handle.
- Withdraw the bit periodically to clear chips from the flutes. Stop the machine before removing wrapped chips with pliers or a brush.
- As the drill nears the bottom surface, reduce pressure slightly so the bit does not grab as it breaks through the aluminum and enters the backing board.
- Retract the drill, turn off the machine, and wait for the bit to stop completely before touching the work.
Do not try to force a clogged drill deeper into the hole. Remove it, clear the flutes, add lubricant, and resume drilling.
Step 5: Deburr and Check the Hole
Drilling leaves a sharp raised edge, called a burr, on one or both faces of the aluminum.
- Use a deburring tool, hand countersink, file, or fine sandpaper to remove the burr from the entry side and exit side.
- Keep the deburring tool flat and use only enough pressure to break the sharp edge. Heavy countersinking can enlarge the hole or create a chamfer you did not intend.
- Brush away all chips and inspect the hole for roughness, tearing, or a ring of smeared aluminum.
- Measure the hole if a bolt, rivet, pin, or other fitted part must pass through it. Test the intended hardware only after the burr is removed.
A smooth hole with clean edges and no raised metal is ready for fastening, tapping, finishing, or assembly.
Drilling Thin Sheet, Large Holes, and Deep Holes
Thin sheet, large plate openings, and deep holes require secure support, suitable cutters, lubrication, chip removal, and deburring to prevent grabbing, tearing, or scoring.
Thin Aluminum Sheet and Holes Near an Edge
Thin aluminum calls for a step drill or a sharp twist drill with wood backing. A step drill is often the easiest choice because it enlarges the hole gradually and supports the thin material better than a large twist drill.
For a safe thin-sheet method:
- Place the aluminum between two flat pieces of scrap wood.
- Clamp the whole sandwich securely so the sheet cannot spin or bend.
- Drill through the wood, aluminum, and lower backing board with a step drill or sharp twist drill.
- Use lubricant and maintain a controlled feed rather than pushing hard at breakthrough.
- Stop the drill, unclamp the work, and deburr both faces by hand.
For holes close to an edge, clamp the aluminum between backing pieces to hold the work steady.
Large, Accurate Holes in Plate
A hole saw or annular cutter can make a large opening in relatively thin aluminum, but a milling machine is the better choice when the hole must be round, accurately located, and precisely sized.
For a large hole through aluminum plate on a vertical machining center, securely fixture the plate, machine the opening with circular interpolation or a suitable cutter, and then finish-bore if the diameter or roundness is critical. Keep clamps outside the cutter path, use coolant or air to remove chips, deburr both sides, and verify the finished diameter with an appropriate measuring tool.
For thick plate, use a rigidly supported drilling setup rather than a handheld drill. The tool can grab, the hole can wander, and the workpiece can become unsafe if it is not rigidly held.
Deep Holes and Chip Packing
Deep holes require extra attention to chip removal. In a deep-through-hole drilling study, 5D holes were treated as a deep-hole case because chip removal and hole accuracy become more difficult at that depth.
For a deep aluminum hole:
- Use a sharp drill designed to evacuate chips, ideally with open or parabolic flutes.
- Lubricate the cutting area and maintain enough feed to form a chip instead of allowing the tool to rub.
- Retract the drill often enough to clear the flutes before chips pack tightly in the hole.
- Continue until the target depth is reached, then deburr the entry and exit edges and inspect the bore for packed chips or scoring.
Do not combine very high RPM with a timid feed on a deep hole. That combination creates friction before the chips have a chance to carry heat away.
Fix Common Aluminum Drilling Problems
| Problem | Likely Cause | Fix |
|---|---|---|
| Bit skates across the surface | No center mark, dull point, or poor alignment | Center-punch plate, use a sharp bit, and start square to the work |
| Aluminum sticks to the bit | Heat, insufficient lubricant, or rubbing instead of cutting | Stop, clean the bit, add cutting fluid, and use steadier feed pressure |
| Long chips wrap around the drill | Chips are not clearing from the flutes | Retract the bit to clear chips; use an open-flute aluminum drill for deeper work |
| Hole is rough or oversized | Bit is dull, flexing, or wobbling | Replace or sharpen the bit, clamp the work, and keep the drill square |
| Back side has a large burr | Bit grabbed at breakthrough or sheet lacked support | Use a wood backing board and reduce pressure near the exit |
| Sheet bends or tears | Workpiece was unsupported | Sandwich the sheet between backing boards and clamp it firmly |
Check the Finished Hole and Protect the Next One
Before moving on, confirm that:
- The aluminum did not shift during drilling.
- Both faces are free of sharp burrs.
- The hole is round enough for its intended fastener, pin, or fitting.
- No chips remain in the hole or on the work surface.
- The drill bit has no aluminum stuck in its flutes or on its cutting edges.
Wipe cutting fluid from the finished piece if it will be painted, bonded, polished, or assembled with another material. Clean and dry the drill bit before storing it; dried-on aluminum and old lubricant make the next hole more likely to run hot.
For the next hole, make a test cut in matching scrap first, confirm that the bit produces clean chips, then drill the finished piece with the same clamped setup.
Frequently Asked Questions
Can You Drill Holes Into Aluminum?
Yes. Aluminum can be drilled with a sharp HSS twist bit, a step drill for thin sheet, or a specialized aluminum drill for deeper holes. Clamp the work securely, use cutting lubricant, and feed the bit firmly enough to make chips rather than letting it rub.
What Kind of Drill Bit Should You Use for Aluminum?
A sharp HSS twist drill is suitable for most holes in aluminum plate and sheet. For deep holes or soft aluminum that produces long chips, an aluminum-specific drill with open flutes is helpful; three-flute designs can balance chip removal and tool strength.
How Do You Drill Aluminum Plate?
Mark and center-punch the location, clamp the plate over a wood backing board, lubricate the drill point, and drill with a sharp bit using steady feed pressure. Retract the bit to clear chips, then deburr both sides after drilling.
How Do You Cut a Large Hole in Aluminum?
Use a step drill for thin sheet, a metal-cutting hole saw or annular cutter for suitable larger openings, or a milling machine when the hole needs close dimensional accuracy. Support the work, lubricate the cutter, clear chips, and deburr both faces when finished.
How Do You Make a 1.69-Inch Hole in 0.79-Inch Aluminum Plate on a VMC?
For a large hole in aluminum plate, fixture the work rigidly and use circular interpolation or a boring operation rather than trying to plunge a full-size twist drill. Finish-bore the opening when size and roundness matter, then deburr the edges and verify the diameter before removing the part from inspection.
Does the Aluminum Alloy Matter When Drilling?
Yes, but the basic method stays the same. Softer aluminum can produce longer, stickier chips, while stronger alloys may require more rigid workholding and a sharper, better-supported tool. In either case, heat, chip buildup, and a dull bit are more likely to cause trouble than the alloy name alone.
Why won’t my drill go through aluminum, and is aluminum hard to drill?
Aluminum is generally easy to machine, but drilling can become difficult when chips clog the flutes or material builds up on the cutting edges. Use a sharp drill and periodically withdraw a non-coolant-through drill so chips can clear from the hole.
